Bullseye-L Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.

Need load data for 180gr LSWC

5 posters

Go down

Need load data for 180gr LSWC Empty Need load data for 180gr LSWC

Post by javaduke Mon Sep 16, 2013 7:53 am

My standard load is 3.5gr Bullseye with 200gr LSWC bullet, and it cycles well and reliable in my 1911 and groups well. I'm trying to figure out the optimal load for the short line with 180gr bullets. Same 3.5gr Bullseye seems to be not enough, what happens is, it has enough power to cock the hammer all the way back, but the case stays in the chamber (or causes the stovepipe). Can anyone recommend a good recipe for the 180gr bullet and Bullseye powder?

Many thanks!

javaduke

Posts : 696
Join date : 2012-07-04

https://bullseyepistolblog.net/

Back to top Go down

Need load data for 180gr LSWC Empty Re: Need load data for 180gr LSWC

Post by Rob Kovach Mon Sep 16, 2013 8:38 am

What is your crimp?
Make the crimp a couple thousandths tighter.  If that doesn't improve the function, add a couple tenths of a grain.  My 185gr load is 3.8gr with .467 crimp.
Rob Kovach
Rob Kovach
Admin

Posts : 2691
Join date : 2011-06-14
Age : 50
Location : Brooklyn, WI

Back to top Go down

Need load data for 180gr LSWC Empty Re: Need load data for 180gr LSWC

Post by Rodger Barthlow Mon Sep 16, 2013 10:02 am

Need more info before I can suggest any course of action.
Slide mounted dot, recoil spring weight, bullet seated depth, brand of primers and crimp. All these things affect function.
 But I will say usually .3gr more of powder and a tight crimp ( .462 ) will get you going with lighter lead bullets.

Need load data for 180gr LSWC 2935285009
Rodger Barthlow
Rodger Barthlow

Posts : 312
Join date : 2013-08-10

Back to top Go down

Need load data for 180gr LSWC Empty Re: Need load data for 180gr LSWC

Post by javaduke Mon Sep 16, 2013 10:21 am

More info: Ultradot Matchdot II slide-mounted, recoil spring is 9lbs, CCI primers and .470 crimp. The same crimp and spring weight works well with my 200gr/3.5gr load. I'll try both tighter crimp and more powder.

javaduke

Posts : 696
Join date : 2012-07-04

https://bullseyepistolblog.net/

Back to top Go down

Need load data for 180gr LSWC Empty Re: Need load data for 180gr LSWC

Post by DavidR Mon Sep 16, 2013 10:22 am

load the 180 to the same as 185 and you will be good, many good loads listed in the sticky on loads of shooters at top of main page
DavidR
DavidR
Admin

Posts : 3032
Join date : 2011-06-10
Age : 70
Location : NRA:Expert, Georgia

Back to top Go down

Need load data for 180gr LSWC Empty Re: Need load data for 180gr LSWC

Post by spursnguns Mon Sep 16, 2013 10:36 am

If your M1911 is being cocked by the load, but the spent cases remain chambered; your extractor needs to have its tension checked and adjusted.  I bet you will find that it is not holding the case properly with these light loads.

Let us know what you find.  Good luck.

Jim
spursnguns
spursnguns

Posts : 603
Join date : 2013-01-04
Age : 65
Location : Nampa, Idaho

Back to top Go down

Need load data for 180gr LSWC Empty Re: Need load data for 180gr LSWC

Post by Rodger Barthlow Mon Sep 16, 2013 2:14 pm

To check the extractor tention remove the slide from the frame and slide an empty case under the extractor. If it dosen't hold the case it's to light and needs more tention. If you remove and bend the extractor becareful not to bend it too much you want it just tight enough to hold the case with a little resistance.
Rodger Barthlow
Rodger Barthlow

Posts : 312
Join date : 2013-08-10

Back to top Go down

Need load data for 180gr LSWC Empty Re: Need load data for 180gr LSWC

Post by spursnguns Mon Sep 16, 2013 3:36 pm

Rodger Barthlow wrote:To check the extractor tention remove the slide from the frame and slide an empty case under the extractor. If it dosen't hold the case it's to light and needs more tention. If you remove and bend the extractor becareful not to bend it too much you want it just tight enough to hold the case with a little resistance.
I've done many a M1911 as you discribed with great success (I typically you a live round and give the slide a little shake).  Nonetheless; for a target pistol I think I would only rely on a Weigand extractor gage and tool (with a good scale).

Jim
spursnguns
spursnguns

Posts : 603
Join date : 2013-01-04
Age : 65
Location : Nampa, Idaho

Back to top Go down

Need load data for 180gr LSWC Empty Re: Need load data for 180gr LSWC

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum