Bullseye-L Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.

Source for grip screws?

2 posters

Go down

Source for grip screws? Empty Source for grip screws?

Post by beeser Wed Jul 09, 2014 8:43 am

I've been looking high and low for some grips screws for my Rink grips and also my S&W Model 41.  The Rink grips require a 2.5 x 30 mm screw.  I have no idea on the size of the 41 screws.  Any suggestions?

beeser

Posts : 1119
Join date : 2014-06-19

Back to top Go down

Source for grip screws? Empty Re: Source for grip screws?

Post by LenV Wed Jul 09, 2014 9:57 am

Grab them quick.

http://www.ebay.com/itm/S-W-Model-41-Grip-Screws-/261527031935?pt=LH_DefaultDomain_0&hash=item3ce439d07f
LenV
LenV

Posts : 4663
Join date : 2014-01-24
Age : 74
Location : Oregon

Back to top Go down

Source for grip screws? Empty Re: Source for grip screws?

Post by beeser Wed Jul 09, 2014 11:27 am

OldMaster64 wrote:Grab them quick.

http://www.ebay.com/itm/S-W-Model-41-Grip-Screws-/261527031935?pt=LH_DefaultDomain_0&hash=item3ce439d07f
No thanks but what size are they?

beeser

Posts : 1119
Join date : 2014-06-19

Back to top Go down

Source for grip screws? Empty Re: Source for grip screws?

Post by LenV Wed Jul 09, 2014 11:33 am

I will take a set apart and see if I can mike them.You will be able to match the thread but you would have to machine the head.Enlongated small head for screw size.
LenV
LenV

Posts : 4663
Join date : 2014-01-24
Age : 74
Location : Oregon

Back to top Go down

Source for grip screws? Empty Re: Source for grip screws?

Post by LenV Wed Jul 09, 2014 12:18 pm

I measured 3 sets to be sure they were all the same. Herrett's were 1.10 inches long.Both the old and new style were 1" screws. Thread size on all of them was .096" ( 4x48 ) .The head size on factory screws is .147. Herrett's were bigger but didn't get that measurement. Length measurements were of the thread only and not an overall measurement.Source for grip screws? Dscf0319
LenV
LenV

Posts : 4663
Join date : 2014-01-24
Age : 74
Location : Oregon

Back to top Go down

Source for grip screws? Empty Re: Source for grip screws?

Post by beeser Wed Jul 09, 2014 12:22 pm

OldMaster64 wrote:I measured 3 sets to be sure they were all the same. Herrett's were 1.10 inches long.Both the old and new style were 1" screws. Thread size on all of them was .096" ( 4x48 ) .The head size on factory screws is .147. Herrett's were bigger but didn't get that measurement. Length measurements were of the thread only and not an overall measurement.Source for grip screws? Dscf0319
Thanks!  That undertaking was very generous and helpful.

beeser

Posts : 1119
Join date : 2014-06-19

Back to top Go down

Source for grip screws? Empty Re: Source for grip screws?

Post by LenV Wed Jul 09, 2014 12:32 pm

No problem.I'm old,bored and putting off going into the shop and getting some welding done.
LenV
LenV

Posts : 4663
Join date : 2014-01-24
Age : 74
Location : Oregon

Back to top Go down

Source for grip screws? Empty Re: Source for grip screws?

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum